top of page

Machine control, Takeoff and Drone Data Education and News

A screenshot from a drone flight planning interface titled “DJI Mavic 3E Flight Planning for Topographic Survey Mapping” shows a mapped area with a green grid overlay and waypoint markers on the left. On the right, advanced settings display sliders for side overlap ratio (80%), frontal overlap ratio (80%), and margin distance. A note emphasizes that 80% overlap provides good photogrammetry results and should not be set below 70% for 3D mapping. A YouTube play button is centered over the image.

A screenshot from a drone flight planning interface titled “DJI Mavic 3E Flight Planning for Topographic Survey Mapping” shows a mapped area with a green grid overlay and waypoint markers on the left. On the right, advanced settings display sliders for side overlap ratio (80%), frontal overlap ratio (80%), and margin distance. A note emphasizes that 80% overlap provides good photogrammetry results and should not be set below 70% for 3D mapping. A YouTube play button is centered over the image.

Quantum Flight Pack - DJI Mavic 3E Training Hub

If you're running a DJI Mavic 3E on a construction site, this is where to start. These training videos cover flight planning, RTK setup, camera settings, and calibration — everything you need to get clean topo data that works with your GPS machine control system.

Quantum Flight Pack - Phantom 4 Pro and Mavic 2 Pro Training

Quantum Flight Pack - Phantom 4 Pro and Mavic 2 Pro Training

Quantum Flight Pack - Phantom 4 Pro and Mavic 2 Pro Training

DJI Phantom 4 Pro and Mavic 2 Pro Topographic Flight Training Videos

Quantum Land Design

Featured Posts

Infographic showing 4 GPS site control principles for machine control: use the design engineer's surveyor, surround the site with control points, calibrate to 5 or more points, and trust but verify with daily checks.

Infographic showing 4 GPS site control principles for machine control: use the design engineer's surveyor, surround the site with control points, calibrate to 5 or more points, and trust but verify with daily checks.

Get Your 3D Grading Under Control: 4 Site Control Principles Every GPS Contractor Needs to Know

Poor site control is the number one problem we see from contractors running GPS machine control. Not bad models or broken equipment. Site control, the first step on every single project. We've seen it cost contractors two weeks of production, turn a correct machine control model on a balanced site into a mysterious site export, and force concrete footings to be redone because the control was rotated 2.8 degrees. Every one of those situations was avoidable.

A screenshot from a drone flight planning interface titled “DJI Mavic 3E Flight Planning for Topographic Survey Mapping” shows a mapped area with a green grid overlay and waypoint markers on the left. On the right, advanced settings display sliders for side overlap ratio (80%), frontal overlap ratio (80%), and margin distance. A note emphasizes that 80% overlap provides good photogrammetry results and should not be set below 70% for 3D mapping. A YouTube play button is centered over the image.

A screenshot from a drone flight planning interface titled “DJI Mavic 3E Flight Planning for Topographic Survey Mapping” shows a mapped area with a green grid overlay and waypoint markers on the left. On the right, advanced settings display sliders for side overlap ratio (80%), frontal overlap ratio (80%), and margin distance. A note emphasizes that 80% overlap provides good photogrammetry results and should not be set below 70% for 3D mapping. A YouTube play button is centered over the image.

Quantum Flight Pack - DJI Mavic 3E Training Hub

If you're running a DJI Mavic 3E on a construction site, this is where to start. These training videos cover flight planning, RTK setup, camera settings, and calibration — everything you need to get clean topo data that works with your GPS machine control system.

Drone Surveying in Construction: Simple, Effective, and Cost-Efficient

Drone Surveying in Construction: Simple, Effective, and Cost-Efficient

Drone Surveying in Construction: Simple, Effective, and Cost-Efficient

Drones simplify construction surveying with just a GPS base/rover and a drone. Affordable, reliable data without the complexity.

Orthographic plan view photo showing how to set up single point GPS site control.

Orthographic plan view photo showing how to set up single point GPS site control.

Single Point GPS Site Control: How to Ensure Accuracy & Avoid Errors

Avoid common pitfalls with Single Point GPS site control—learn to ensure stable, accurate results and avoid costly mistakes in grading.

Follow Us

Recent Posts

How to Read an AGTEK Volume Report

How to Read an AGTEK Volume Report

How to Read an AGTEK Volume Report

Infographic showing 4 GPS site control principles for machine control: use the design engineer's surveyor, surround the site with control points, calibrate to 5 or more points, and trust but verify with daily checks.

Infographic showing 4 GPS site control principles for machine control: use the design engineer's surveyor, surround the site with control points, calibrate to 5 or more points, and trust but verify with daily checks.

Get Your 3D Grading Under Control: 4 Site Control Principles Every GPS Contractor Needs to Know

AgTek cut/fill and plansheet in google earth.

AgTek cut/fill and plansheet in google earth.

Bart Booth - Quantum's Earthwork Takeoff Pro

Tenstar virtual training space showing an excavator simulator, VR operator stations, and a 3D jobsite model displaying how people and machines interact in a simulated construction environment.

Tenstar virtual training space showing an excavator simulator, VR operator stations, and a 3D jobsite model displaying how people and machines interact in a simulated construction environment.

Introducing Tenstar Simulators: A Smarter Way to Train Operators Before They Hit the Jobsite

bottom of page